srodocker
Well-known member
- 6,549
- 69
- 48
- Location
- Lacey, Washington
oooo im excited to see one of those little mv's amer team!
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
2011 PNW Mini Rally #4
- Thread starter srodocker
- Start date
Amer-team
Well-known member
- 1,707
- 32
- 48
- Location
- Centralia/WA
Hope I can make it, but don't want to hold anyone up. The A1 has a top speed of about 50 and the 715 about 45 MPH.
Both are originals, meaning, not restored. Touched up, yes, restored, no.
Both are originals, meaning, not restored. Touched up, yes, restored, no.
- 740
- 162
- 43
- Location
- Gainesville, Florida
I recently sold one of my M105A2 trailers and have a good complete set of bows as well as the rear gate. (both wood) I'd bring those with me to the meet if anyone is interested. Say $50 for the complete package?
hwcurtice
Well-known member
- 1,558
- 35
- 48
- Location
- Moncks Corner, SC
I forget, will the bow set fit the a2 trailer?
- 740
- 162
- 43
- Location
- Gainesville, Florida
This set is made for the M105-A2 trailer but not the smaller M101-A2 trailer. Which one do you have?
hwcurtice
Well-known member
- 1,558
- 35
- 48
- Location
- Moncks Corner, SC
hwcurtice
Well-known member
- 1,558
- 35
- 48
- Location
- Moncks Corner, SC
Say Jinx, do you know merlot566jka?
Lives in Gold Bar, but is a sailor out at sea ATM. He says a neighbor of his has a m35A2. I guessing this might be you. Sorry, don't know his real name...
Lives in Gold Bar, but is a sailor out at sea ATM. He says a neighbor of his has a m35A2. I guessing this might be you. Sorry, don't know his real name...
64c30
New member
- 94
- 0
- 0
- Location
- Spanaway WA
Having the Hemmt is half the battle.
When we did engine swaps with my 816 in Germany, it took about 3 hrs from start to finish. But, we had the lift bar and all else.
We'll try to be there. I hold a Coke can and watch VERY well!
Last edited:
srodocker
Well-known member
- 6,549
- 69
- 48
- Location
- Lacey, Washington
sweet cant wait to see ya!
Stalwart
Well-known member
- 1,739
- 33
- 48
- Location
- Redmond, WA
Dan and I will need to speak before the date so we can set the vehicles in the best spot for the operation. I'm still trying to feed enough grease into my turntable to get it to move smoothly, it's getting better but it sometimes jumps a bit. I ususlly try not to slew the crane with it loaded, instead extend/retract. raise/lower the boom and use the winch to do most of my movements. It is a small crane, but it can still maim and kill. I also think they used a big hyd. motor to get a high maximum slew rate for speed where they probably should have used a very small motor and geared it for precise movements. The Stalwarts used for REME (battlefield mechanics) were valved completely differently for precise movements.
We'll just have to be prepared, communicate, work carefully and it should go smoothly. I've done a ton of lifting with this thing and no one has gotten so much as a bruise.
We'll just have to be prepared, communicate, work carefully and it should go smoothly. I've done a ton of lifting with this thing and no one has gotten so much as a bruise.
Josh
Active member
- 1,678
- 12
- 38
- Location
- Portland, Oregon
Im ready to turn a wrench and repay the help that I have been given over the years.
wsucougarx
Well-known member
- 6,951
- 67
- 48
- Location
- Washington State
Just a side note, it appears this is going to be a fairly large rally. Is there an overflow lot for us to park in
. You guys are going to need a fairly large work area to account for the HEMTT, deuce, and a cleared area for the crane to operate.
. You guys are going to need a fairly large work area to account for the HEMTT, deuce, and a cleared area for the crane to operate.
srodocker
Well-known member
- 6,549
- 69
- 48
- Location
- Lacey, Washington
Me and dan yesterday were talking about the layout and we think we have it layed out pretty well. hopefully...hehe
Josh
Active member
- 1,678
- 12
- 38
- Location
- Portland, Oregon
Just a side note, it appears this is going to be a fairly large rally. Is there an overflow lot for us to park in
I think he has a horse field with some good mud
.Otherwise, the street looked to wide enough that some rigs could be parked on it if needed.
wsucougarx
Well-known member
- 6,951
- 67
- 48
- Location
- Washington State
OK, if needed I can just drive my civy to save space
Josh
Active member
- 1,678
- 12
- 38
- Location
- Portland, Oregon
hwcurtice
Well-known member
- 1,558
- 35
- 48
- Location
- Moncks Corner, SC
googlemaps: Looks like he has a big enough spread to park in. And plenty of trees for coffee watering too!
And no neighbors to bother with all the diesel belching.
And no neighbors to bother with all the diesel belching.
wsucougarx
Well-known member
- 6,951
- 67
- 48
- Location
- Washington State
LOL, ahh you guys will be drooling all over the HEMTT. Hey Josh, we can probably all convoy there together like we did last time with Aaron and Ed. Are we planning on doing a BRIEF stop at Brad's along the way? Just need to try and time it like we did last time. It was funny I literally just hit the overpass and looked on I-5 and saw you guys coming around the corner...
srodocker
Well-known member
- 6,549
- 69
- 48
- Location
- Lacey, Washington
my deuce and 1 of my trailers should be moved to save some space. they will be tucked next to his barn.
one of my trailers though will not be. stuart can i have you lift a bed out of my deuce bed onto a trailer? along with my oil tote? or josh can you throw them on my new trailer for me? have about 50-60 gals of oil in the tote. brad doesnt have a 105 bed so might go with the smaller 101 bed...dunno yet we'll see.
one of my trailers though will not be. stuart can i have you lift a bed out of my deuce bed onto a trailer? along with my oil tote? or josh can you throw them on my new trailer for me? have about 50-60 gals of oil in the tote. brad doesnt have a 105 bed so might go with the smaller 101 bed...dunno yet we'll see.
- 740
- 162
- 43
- Location
- Gainesville, Florida
Don't know him personally, but I do know another person in the area with a deuce. He lives right along highway 2.